Anuthane
Sealer
Aliphatic Polyurethane Premium Coating
Anuthane Sealer is air drying two-component, extremely durable, high solids, acrylic polyurethane sealer with superior sanding and high build properties.
Recommended uses
Anuthane Sealer is used mainly for exterior finishing of wood. It is recommended for application over particle board, veneer and open pore substrates. Also suitable for variety of timbers such as rubber wood, pine wood, nyatoh, oak, etc.
Surface Preparation:
Wood: Always select seasoned wood for excellent
wood finishing. The wooden surface to be coated must be dry and free from dust,
oils, grease and other foreign matter. Sand the surface with dry sandpaper no.
180 or with any other suitable type until the surface is smooth. Remove all
dust. Fill the grains with Anupam Wood Filler and after drying, sand with
sandpaper no. 280 or 320.
Mixing and Application:
Mix base and hardener components of Anuthane Sealer in recommended ratio in a clean container. Do not mix more than can be used within 8 hours. Allow the mixture to mature for 30 minutes before application. Apply a coat of Anuthane Sealer and after 16 hours of drying, scuff with sandpaper no. 320 or higher. Remove all dust. Further coats are recommended until the surface becomes smooth. If wood stains are required, apply a coat of spirit based or water based stain on the sealer. Apply a coat of Anuthane Enamel (clear or pigmented) as suggested above for Anuthane Sealer . More coats can be applied for achieving desired finish.
TECHNICAL DATA
|
Name/Description |
Anuthane Sealer |
|
Type |
Two pack cold cured |
|
Composition |
Acrylic Aliphatic Polyurethane |
|
Colour |
Chalky, Pale White |
|
Volume Solids (mixed) |
43± 3% |
|
Mixing Ratio |
Base : Hardener 4 : 1 by volume |
|
Pot Life @ 30° C |
6 to 8 hours |
|
Dry film thickness per coat |
30 microns |
|
Coverage-(theoretical-no loss) |
15 m² /litre |
|
Serviceability @ 30°
C
Dry to touch
Hard Dry
Recoat Full Cure |
30 minutes
Overnight
16 hours 7 days |
|
Induction (Sweat-in-time) @ 30° C |
30 minutes |
|
Dry heat resistance |
120° C |
|
Relative Humidity |
85% |
|
Application Temperature
-minimum -maximum |
10° C 35° C |
|
Solvent/Thinner |
Anusol - PUT |
|
Flash Point |
23° C |
|
Packing |
4 & 20 litres |
|
Shelf Life |
6 months |
|
Precaution |
Flammable. Keep away from heat and open flame. Maintain good ventilation and avoid breathing vapours. |
Notes
Spray equipments should be cleaned with Anusol - PUT.
The contents should be stirred thoroughly prior to use.
After mixing Base and Hardener in recommended proportions, allow for 30
minutes induction period or sweat-in-time (maturing) before application.
Precaution should be taken to close immediately the Hardener component
since the Hardener is very susceptible to atmospheric moisture.
This coating should always be thinned with Anusol - PUT. The use
of alternative thinners can severely inhibit the curing mechanism of the
coating.
Disclaimer:
Information provided herein is based upon tests believed to
be reliable. It does not guarantee the results to be obtained. Nor does it make
any express and implied warranty or merchantability, or fitness for a particular
purpose concerning the effects or results of such case. It does not release you
from the obligation to test the products supplied by us as to their suitability
for the intended uses. The application, surface preparation and use of the
products are beyond our control and, therefore, entirely your own
responsibility.