Anuthane 301
Polyurethane Clear Coating for Wood
Anuthane 301 wood coating is a two component, fast curing, highly durable 100% polyurethane natural wood finish for interior application.
Features and Benefits
Excellent wood grain natural finish
Excellent adhesion to most wooden surfaces
Stain Resistant / Washable
Scratch Resistant
Good Heat Resistance
Acid & Alkali Resistant
Glossy / Matt Finish
Spirit & Water Resistant
Protects the Wood for many years
Economical with minimal maintenance
Recommended Uses:
|
Office and Household Furniture |
Wardrobes |
|
Kitchen Cabinets |
Antiques |
|
Musical Instruments |
Bar Furniture |
|
Hospital Furniture |
Sports Goods |
|
School Furniture |
Most Wooden Surfaces |
TECHNICAL DATA
|
Name/Description |
Anuthane 301 Sealer |
Anuthane 301 Finish |
|
Type |
Two pack cold cured |
Two pack cold cured |
|
Composition |
Polyester/Polyurethane |
Polyester/Polyurethane |
|
Colour |
Clear |
Clear |
|
Finish |
Matt |
Matt and Glossy |
|
Solvent/Thinner |
Anusol – 301 Thinner |
Anusol – 301 Thinner |
|
Mixing Ratio |
Base : Hardener 3 : 1 by volume |
Base : Hardener 3 : 1 by volume |
|
Pot Life @ 30 ° C |
6 to 8 hours |
6 to 8 hours |
|
Dry film thickness per coat |
40-50 microns |
25 microns |
|
Coverage-(theoretical-no loss) |
100-120 sq. ft/litre |
100-120 sq. ft/litre |
|
Serviceability @ 30 ° CDry to touch Sanding Time Re-coat Packing Time |
Within 1 hour Within 6-8 hours 8-12 hours 24 hours minimum |
Within 1 hour Within 6-8 hours 8-12 hours 24 hours minimum |
|
Dry heat resistance |
120 ° C |
120 ° C |
|
Application Temperatures -minimum -maximum |
15° C35 ° C |
15° C35 ° C |
|
Flash Point |
25 ° C |
25 ° C |
|
Packing |
4 & 20 litres |
4 & 20 litres |
|
Shelf Life |
6 months |
6 months |
|
Precaution |
Flammable. Keep away from heat and open flame. Maintain good ventilation and avoid breathing vapours. |
Flammable. Keep away from heat and open flame. Maintain good ventilation and avoid breathing vapours. |
Mixing and Application:
Always select seasoned wood for excellent wood finishing. The wooden surface to be coated must be dry and free from dust, oils, grease and other foreign matter. Sand the surface with dry sandpaper no. 180 or with any other suitable type until the surface is smooth. Remove all dust. Fill the grains with Anupam Wood Filler and after drying, sand with sandpaper no. 280 or 320.
Mix base and hardener components of Anuthane 301 Sealer in recommended ratio in a clean container made of either steel, glass or plastic. Do not mix more than can be used within 8 hours. Allow the mixture to mature for 15 minutes before application. Apply a coat of Anuthane 301 Sealer and after 8 hours of drying, scuff with sandpaper no. 320 or higher. Remove all dust. Further coats are recommended until the surface becomes smooth. If wood stains are required, apply a coat of spirit based or water based stain on the sealer. Apply a coat of Anuthane 301 Finish as suggested above for Anuthane 301 Sealer. More coats can be applied for achieving desired finish.
Notes:
Disclaimer:
Information provided herein is based upon tests believed to be reliable. It does not guarantee the results to be obtained. Nor does it make any express and implied warranty or merchantability, or fitness for a particular purpose concerning the effects or results of such case. It does not release you from the obligation to test the products supplied by us as to their suitability for the intended uses. The application, surface preparation and use of the products are beyond our control and, therefore, entirely your own responsibility.